Free written estimates in Snohomish, King & Skagit Counties — 425-415-6773
31503 SR 2, Sultan, WA | Mon–Fri 8am–4pm
Guide

How much does fascia board replacement cost in Snohomish County?

What rotted fascia costs to replace when it is done with new gutters, what moves the price, and how to tell if yours has gone soft.

Replacing a fascia board (the board your gutters attach to) costs about $7 to $22 per foot in 2026, so a full single-story roofline runs $1,050 to $3,300. National figures from Angi’s 2026 fascia cost guide. Most Snohomish County homes don’t need all of it. Rot sits in a few sections behind a leaking corner or downspout. Replacing those while the gutters are off costs a fraction of a full job. Market figures, not Pro Flow prices.

Painted wood fascia board with a white gutter at the roof edge of a lap-sided house, the board that fascia board replacement cost in Snohomish County covers

What is the fascia board, and why does it rot here?

The fascia is the flat board that runs along the edge of your roof, nailed to the ends of the rafters. Your gutters hang from it. It also closes off the roof edge so wind and rain can’t get into the attic.

On most homes in Snohomish, King and Skagit Counties it is a wood board, painted or primed. Wood is fine as long as it stays dry. The problem is that the fascia sits in the wettest spot on the house. Water that overflows the back of a gutter, or leaks at a corner, runs straight down the face of the board and into the end grain.

Western Washington gives that water plenty of time to work. It rains on 17 to 22 days a month in winter in the lowlands, according to the Western Regional Climate Center. A board that never dries out decays.

Research from the U.S. Forest Service’s Forest Products Laboratory (Carll and Highley, 1999) puts the sweet spot for decay fungi above fiber saturation, about 25 to 30 percent moisture, and treats 20 percent as the safe line. Wet fir needles packed against the board hold it well above that for months.

Thumbtack’s fascia cost data (July 2026) says well-maintained wood fascia lasts 15 to 20 years. Here, a board behind a leaking gutter can go soft in far less.

What does fascia board replacement cost in 2026?

Fascia is priced by the foot. Angi’s national data (updated October 8, 2026) puts materials and labor together at $7 to $22 per linear foot, with an average project at $2,500. Here is how that scales with the length of your roof edge.

Feet of fasciaCost range (Angi, 2026)
50 feet (one side or a garage)$350–$1,100
100 feet$700–$2,200
150 feet$1,050–$3,300
200 feet (typical two-story home)$1,400–$4,400
300 feet$2,100–$6,600

Labor is the bigger half. Angi and This Old House (updated March 2026) both put installation labor at $6 to $20 per foot, with the board itself at $1 to $20 per foot depending on the material. This Old House’s full range stretches to $40 per foot when you include premium boards and tall, hard-to-reach rooflines.

Angi does not publish a Snohomish County figure. Its closest regional number is Oregon, at $1,300 to $3,100 for a typical job, which is a fair guide for the Seattle area too. Add 7 to 15 percent for a second story or a steep lot, per HomeAdvisor (updated June 2026).

How much does it cost with new gutters?

This is where the numbers change. A standalone fascia job pays a carpenter to take the gutters down, do the woodwork and put the gutters back. When the fascia is replaced during a gutter installation, the gutters are already coming down. You pay for the boards and the time to fit them, not for a separate visit.

The other saving is that you rarely need the whole roofline. We take the old gutters down first and check the wood behind them. Rot shows up in sections: the corner where a joint leaked, the stretch under a clogged downspout, the end of a board where water got into the grain. Here is what that looks like, using Angi’s $7 to $22 per foot. This is our arithmetic, not a published figure.

How much fascia is rottedAdded to a gutter job (our arithmetic on Angi’s range)
A few sections, 10–20 feet$70–$440
One full side, 40–60 feet$280–$1,320
Whole roofline, 150–200 feet$1,050–$4,400

For the gutters themselves, our guide to how much new gutters cost in Snohomish County works out to roughly $1,900 to $3,900 for 150 to 200 feet. So a typical job with a couple of rotted sections replaced lands near the gutter price, not double it.

That is how our seamless gutter installation in Snohomish County handles it: we replace rotted fascia boards before the new gutters go up, so nothing hangs on bad wood. The same applies to gutter repair in Snohomish County. When a gutter has pulled away from the house, we replace the rotted board behind it and rehang the gutter on solid wood.

Your written quote lists any fascia repairs as their own line, so you can see what the wood adds.

Why can’t you hang new gutters on rotted fascia?

Because the fascia is what holds the gutter up. Our gutters hang on Alu-Rex T-Rex brackets, a continuous hanger that screws into the fascia along its whole length. A screw into soft wood holds for a season. Then the gutter sags, the slope goes wrong, and water pools and overflows at the low spot.

Angi’s gutter data puts hangers every 2 to 3 feet on a standard install, and each one needs solid wood behind it. Wrapping a rotted board in aluminum, which some installers offer, hides the problem without fixing it. The rot keeps spreading behind the metal, and it can reach the rafter tails. HomeAdvisor puts dry rot repair at $500 to $4,000 once it goes that far.

Which fascia material should you choose?

Wood is the cheapest board and the one that rots. The alternatives cost more per foot but don’t need paint and don’t decay. These material prices are per foot, board only, from HomeAdvisor and This Old House (2026).

MaterialBoard cost per footWhat to know
Wood (primed pine or cedar)$1–$3Must be painted or sealed on every face, including the cut ends. Cheapest to buy, most upkeep.
Fiber cement$1–$5Doesn’t rot. Heavier, and it needs the right fasteners.
PVC$3–$7Made to look like wood grain and won’t rot. A good match for the wettest walls.
Composite$1–$8Wood fiber and resin. Resists water better than plain wood.
Aluminum (wrap or cover)$8–$20Usually a cover over a wood board. Fine over sound wood, a mistake over rot.

In Snohomish County’s wet winters, the cheap board is the expensive one. If you choose wood, ask that it be primed on all sides before it goes up, and that the cut ends be sealed. If the same section has rotted twice, PVC or fiber cement is worth the extra few dollars a foot.

How do you know your fascia has rotted?

You can check most of this from the ground. Walk the house after a rain and look at the roof edge.

  1. The gutter has sagged or pulled away from the house. This is the most common sign. The hanger screws have lost their grip because the wood behind them has gone soft.
  2. Paint is bubbling or peeling along the roof edge. Paint lifts when water gets behind it. The board underneath is probably wet.
  3. Dark streaks or stains below the gutter. Water is running behind the gutter, not into it. It is soaking the fascia on the way down.
  4. The board is soft. Press a screwdriver into it near a corner or a downspout. Sound wood resists. Rotted wood takes the tip with no effort.
  5. Water drips between the gutter and the house in rain. Either the gutter has tipped back or a joint has failed. Both put water on the fascia.
  6. Hangers or nails have backed out. If you can see the fasteners standing proud, the wood isn’t holding them.

If your gutters overflow but aren’t clogged, read why gutters overflow in heavy rain. Two of the six causes there, a sagging gutter and water shooting behind it, usually trace back to the fascia.

Should you repair or replace the fascia?

Rot at one end of a board, with the rest sound, is a section replacement. We cut back to solid wood, fit a new piece, and seal the joint. A board that is spongy along its length, or soft at every hanger, gets replaced whole.

The one thing we check before either is the rafter tails, the ends of the roof framing the fascia nails to. If rot has reached them, that is a carpentry and roofing job beyond gutters, and we will tell you so before any work starts. We don’t do roofs, siding or windows.

One source of confusion: this guide is about the fascia board. We also install fascia-style gutters, a tall, flat gutter that attaches to the rafter ends and takes the place of the board. That is a different product, and it suits newer homes with long, straight rooflines.

How to compare quotes for fascia and new gutters

Two quotes can be $500 apart because one includes the woodwork and the other doesn’t mention it. Before you compare prices, check that each quote says:

  • Which sections are being replaced and how many feet, not just “fascia repair as needed”.
  • What board goes in, and whether wood is primed on all sides and sealed at the cuts.
  • Who takes the gutters down and rehangs them, and whether that is in the price.
  • Whether the drip edge is checked or replaced. A missing drip edge is a common reason the board rotted in the first place.
  • Whether old boards and gutters are hauled away.
  • That it is in writing, with the fascia as its own line, so a surprise behind the old gutter doesn’t become a surprise on the bill.

We replace rotted fascia with new gutters across Snohomish County, including Everett, Monroe, Lake Stevens and Sultan, as well as north and east King County and Skagit County. The estimate is free, in writing, with no pressure.

Common questions

Fascia runs about $7 to $22 per foot in 2026, per Angi. Most homes only need a few sections replaced, which adds $70 to $440 on our arithmetic. A whole roofline of 150 to 200 feet is $1,050 to $4,400. Doing it with the gutter install saves the separate visit to take the gutters down and put them back.

No. The hanger screws need solid wood, and a screw in rotted wood lets go within a season. We take the old gutters down, check the wood, replace any rotted sections and only then hang the new gutters.

We replace rotted fascia as part of installing or repairing gutters, because that is when the boards are exposed. For fascia work with no gutter work, you want a carpenter or a roofer.

The fascia board is the wood trim at the roof edge that standard gutters hang from. Fascia-style gutters are a tall, flat gutter that attaches straight to the rafter ends and replaces the board. This guide is about the board.

Paint seals the surface, but rot is inside the wood. It keeps spreading under the new paint and reaches the hangers and rafter tails. Cutting the soft section out and fitting new wood is cheaper than the repair that follows.

Pricing disclaimer: the cost ranges on this page are third-party market data for 2026, from Angi, This Old House, HomeAdvisor and Thumbtack (national figures), included for context only. They are not a Pro Flow Gutters price list. Actual prices depend on how many feet of fascia have rotted, the board you choose, roof height and access around the house. Contact Pro Flow Gutters for a free, no-obligation written estimate, or call 425-415-6773.

Get a free written estimate

Call us or send your address. We will get back to you within 24 hours on business days to book a time to look at your gutters.

Call 425-415-6773Free estimate